WINDOWS 9X拨号上网的设置

准备Preparation

要用WINDOWS 9X拨号入网，必须安装了下列：

如图：
network.gif (8331 字节)

一.首先安装Microsoft 网络客户(Client for Microsoft Networks) （一般Windows95是省却安装了的，如果有了就不用安装）

  1. 双击我的电脑(Click on My Computer), 然后控制面板(Control Panel), 然后网络 (Network)
  2. 点添加Add option)
    network1.gif (5626 字节)
  3. 选增加客户Client
  4. 选Microsoft
    client.gif (5713 字节)

二、添加 TCP/IP 协议 (Microsoft TCP/IP Protocol)

  1. 单击添加Click Add option
  2. 选协议Choose to add Protocol
  3. 选Microsoft
    tcpip.gif (5624 字节)
  4. 双击TCP/IP协议 Double click on TCP/IP 。之后你会在网络里看到下图：
    network2.gif (8331 字节)
  5. 双击拨号网络适配器，打开它的属性 （如果未安装拨号网络适配器，看“三、添加拨号网络适配器）
    点选绑定一项，看到：

    bind.gif (4319 字节)

    如果看到拨号网络适配器已经绑定在Tco/ip上， 重新启动后一般就可以成功上网了。

三、添加拨号网络适配器(Microsoft Dial-UP Adapter)
（适合那些Windows没自带驱动程序的Modem）

  1. 在控制面板的网络里选添加Click Add option
  2. Choose to add Adapter选网络适配器
  3. 选驱动程序：把Modem带的驱动程序盘插上，按"从磁盘安装"
    add_modem.gif (7159 字节)
  4. 安装完一路按OK退出，你会看到Tcp/ip和你的Modem捆在一起了：
    tcp_ip_modem.gif (2041 字节)

    之后重新boot机

另外如果你没有用其他网络，请把其他协议，比如NetBEUI等删掉。

Since Windows 95 tries to do everything for you, you may need to Remove any protocols, clients and/or adapters that are not in the picture. If you do find them listed in the installed components section, simply highlight the extra items and click on the remove button.

Tcp/IP 设置

　

　

（以下一般为省却就有的，可以直接进行下一步）

Now that you have installed these components, you can go ahead and configure the settings for each item. It may be a bit confusing at first, but if you follow this simple procedure, you should have no problem connecting to ChinaNet.

一.设置TCP/IP的属性（以下一般为省却就有的）

按确定退出再boot机

　

Dial-Up Adapter

  1. Double click on Dial-Up Adapter
  2. Select TAB Driver Type
    Check the box Enhance mode (32 bit and 16 bit) NDIS driver
  3. Select TAB Bindings
    Check the box TCP/IP
  4. Select TAB Advance
  5. Set Record a Log file to no
    Set Use IP header compression to yes
  6. Click OK

Next we head over to TCP/IP

  1. Double click on TCP/IP Select TAB IP Address
    Check on the box Obtain an IP Address Automatically
  2. Select TAB GATEWAY
    Enter "0.0.0.0" as the New Gateway and press Add
  3. Select TAB Binding Leave a check mark on Client for Microsoft Network
  4. Select TAB WINS Configuration Check the box Disable WNIS Resolution
  5. Select TAB "Advanced" Check the box None as your selection

After rebooting the system, you will need to run Microsoft Dial-Up Networking program. Win95 may have this installed during its installation procedure. You can find it under the "My Computer" icon. If you have this program installed, proceed on to next step.

安装拨号网络(Microsoft Dial-Up Networking)

　

  1. 选控制面版(Control Panel)
  2. 双击添加/删除程序(Add/Remove Programs)
  3. 双击通讯再选拨号网络(Communication and check on Dial-Up Networking)
  4. 确定OK

setup.gif (8442 字节)

Windows 95会提示你下一步怎么做， 安装完之后会在我的电脑出现拨号网络图标：
my_comp.gif (5705 字节)

二，安装具体的拨号网络

  1. 打开我的电脑,再双击拨号网络
  2. 双击新建连接(Click on Make New Connection)
    newnet.gif (5828 字节)
  3. 先选好MODEM，再走下一步(Select your modem and click NEXT)
  4. 输入ChinaNet（或其他）作为标题(Enter ChinaNet as the title )
  5. 填163作为电话号码，区号填20.
  6. 完成(Click Finish)

然后改变其属性(Next, you will need to change its properties).

  1. 在拨号网络中点选China Net,右击
  2. 选属性(Use your RIGHT mouse, select properties)
    properties.gif (5023 字节)
  3. 选配置(Select Configure )
  4. 点选项(Select Option TAB )
  5. 选拨号后出现终端窗口(Leave a check in "Bring Terminal window After Login" *It is a MUST that you leave a check in this box*)
    terminal.gif (2669 字节)
  6. 确定 OK
  7. 选服务器类型Select Server Type
    servr.gif (4868 字节)
  8. In Type of Dial-Up Server. 拨号服务器类型, 选PPP: Windows 95, Windows NT 3.5, Internet 其他只选TCP/IP
  9. 点击TCP/IP设置
  10. 上面选已分配IP地址
  11. 在下面选命名服务器的地址,在 DNS 中填: 主控：202.102.9.141, 其它不用填

    ip1.gif (10082 字节)

    确定(Click on OK.)

五，开始拨号

  1. 双击ChinaNET图标(Double click on the FJnet Icon )
  2. 不用填帐号和密码
  3. 按连接(Select connect )
  • You will wait until the dialing windows(等拨号终端) comes out
  • 当出现拨号终端后，请把您的帐号和密码填上，

    t13.gif (5323 字节)

    ChinaNet用户，当出现乱码后按F7即可

    当出现：
    14h-con.gif (2399 字节)

    您已经成功上网了，请尽情享受网络的乐趣吧!